Search:

Type: Posts; User: Jack Innes

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,933

    Fastenal has a good shipping set up in the US. ...

    Fastenal has a good shipping set up in the US. Tie it down to a skid & send it. The buyer can pay them. A friend had a seat from a fire truck sent from Maine to Indy. at a cost of $100. The...
  2. Replies
    7
    Views
    2,679

    Hello, Where are you located & what is the price...

    Hello,
    Where are you located & what is the price now?
    Thank you,
    Jack
  3. Thread: Henderson

    by Jack Innes
    Replies
    3
    Views
    4,920

    Eric, Thank you for identifying the engine -...

    Eric, Thank you for identifying the engine - probably expensive parts. You are correct on the hopeful aviators & sadly many such projects do not go much further than butchering an engine.

    Jack...
  4. Thread: Henderson

    by Jack Innes
    Replies
    3
    Views
    4,920

    Henderson

    Heads Up! This is advertised on the Smokstak site. It looks interesting & might be of use to a Henderson project. I know nothing about the engine or the seller.

    see: ...
  5. Replies
    1
    Views
    1,409

    1905 - 1913 single

    Hello,

    Does anyone know the size of the hole & the size of the crank pin (HD part no AA-19) used on the early Harley Davidson singles? I understand the crank pin is a press fit.

    Thank...
  6. Replies
    3
    Views
    1,694

    Mark, I am 99% sure that your sprocket...

    Mark,

    I am 99% sure that your sprocket http://www.ebay.com/itm/Unknown-Engine-Sprocket-Harley-Indian-Excelsior-Thor-Henderson-Flying-Merkel-/252843033125?hash=item3ade9e8225:g:SgsAAOSwmgJY4ou9 ...
  7. Replies
    0
    Views
    1,011

    Splitdorf Generator

    Does anyone have a modern part no. for replacement bearings for a Splitdorf DU 1 generator? This is the earlier model with both bearings the same. The OD of the outer race is 1.00".

    Thank you,...
  8. More pictures.

    More pictures.
  9. Here are some pictures of the attachments. The...

    Here are some pictures of the attachments. The lower balls are 1" dia. & the upper one is 1 1/8". All are worn a bit.
    You will see an original RS mount at the front that is not used.
  10. I have the same National Model V chassis with the...

    I have the same National Model V chassis with the "Vibrasorber" upper connection that was always on my Reading Standard. It used the ball under the seat & a clamp on ball front & back. I will take...
  11. Replies
    7
    Views
    4,612

    Sidecar springs

    Hello, Does anyone know of a supplier of sidecar springs like the one shown here?

    This is the sidecar that was on my 1919 Reading Standard from about 1920.
  12. Replies
    0
    Views
    860

    Model F Connecting Rods

    Hello, Could someone give me the measurements of model F connecting rods please.
    I need the center to center length, big end width, & piston pin size. A picture would be helpful as well.
    Thank...
  13. Replies
    1
    Views
    1,230

    What is the diameter & the compression height...

    What is the diameter & the compression height (center of pin to top of piston) ?

    Jack
  14. Replies
    5
    Views
    3,247

    Thank you Chuck - WTT looks like a place well...

    Thank you Chuck - WTT looks like a place well worth visiting!

    Jack
    AMCA #30270
  15. Replies
    5
    Views
    3,247

    Thank you Craig, I would like to see it but I...

    Thank you Craig, I would like to see it but I can not find any clues to tell me what a WTT is???

    Jack
  16. Replies
    0
    Views
    809

    Reading standard parts

    Hello, I am looking for the following for a Reading Standard Twin

    1921 engine parts;

    - crankshaft (ball bearing mains)
    or -flywheels
    -rods
    -3 shafts

    -pistons &...
  17. Replies
    5
    Views
    3,247

    New Member from Ontario:

    Hello all, I am Jack Innes from Brooklin, Ontario, Canada & have recently joined the AMCA. I have had motorcycles since I was 14 & the first vehicle I had registered on the road was a 1960 HD...
Results 1 to 17 of 18