Search:

Type: Posts; User: Omarttentmaker

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    239

    Yeah, I think that's the one I got. My...

    Yeah, I think that's the one I got. My measurement was from the top of that lip to the backside. Thanks for the info.
  2. Replies
    3
    Views
    239

    juice rear brake drum widths

    Does anyone know the width difference between the early and late brake drums for duo-glide/electra=glide? I just took the drum off a '65, and it has a cast number on the back of the drum, but the...
  3. Replies
    9
    Views
    536

    OK....Thanks again

    OK....Thanks again
  4. Replies
    9
    Views
    536

    OK, thanks for the tips. Just a couple questions....

    OK, thanks for the tips. Just a couple questions. First, for Cotten, what's that flange piece with the screws in it for? And for Larry, when you true up the flange, do you fixture it in the lathe by...
  5. Replies
    9
    Views
    536

    cylinder boring

    Want to put new pistons in my panhead. Made a ring fixture to mount in a 4 jaw chuck. OD and ID run true, has 4 holes in the face to mount the cylinder. Trued the ID in the lathe and made the hole a...
  6. Replies
    19
    Views
    5,943

    Snap-On used to make a small enough box-end with...

    Snap-On used to make a small enough box-end with a 3/8" square on the opposite end that would fit on a torque wrench for tightening head and base bolts. here's a pic of the 2 of them. I had to...
  7. Replies
    4
    Views
    426

    Found a stray piece of 4140.....Harder than...

    Found a stray piece of 4140.....Harder than cold-rolled, so I whipped up a .008" diameter larger roller. Works appreciably better.
  8. Replies
    4
    Views
    426

    I did that once with the bars on my flathead...

    I did that once with the bars on my flathead bobber, but it was a fairly long, involved process. Maybe I'll try turning up a soft roller. My first thought was to make one from a piece of O-1 drill...
  9. Replies
    4
    Views
    426

    Throttle slop

    Does anybody know anyone who makes oversize rollers that fit into the throttle slot on hydra-glide bars? My throttle slot has some wear in it, and the roller that slides in it needs to be about .005"...
  10. Replies
    4
    Views
    587

    So WL's up to '52 and servicars up to '56 came...

    So WL's up to '52 and servicars up to '56 came from the factory with 2-piece 18 MM spark plugs?
  11. Replies
    4
    Views
    587

    Thanks, Rubone. Maybe they were for servicars.

    Thanks, Rubone. Maybe they were for servicars.
  12. Replies
    4
    Views
    587

    Anybody ever seen these?

    I was looking thru my spark plug collection today, and these turned up. They're 18 MM with screw-on knurled nuts to hold the "shepherd's crook" ends on old coil wires. The thing that got me is that...
  13. Replies
    6
    Views
    766

    Yeah, Buna is not for everyone.

    Yeah, Buna is not for everyone.
  14. Replies
    6
    Views
    766

    Yes, I do have a good petcock. We had discussion...

    Yes, I do have a good petcock. We had discussion that earlier. You remember, extra virgin olive oil and cigarette ashes to lap in the seat in the shut-off fitting?
  15. Replies
    6
    Views
    766

    Not that I doubt you, Mr, Cotten, but here's a...

    Not that I doubt you, Mr, Cotten, but here's a pic of two of the o-rings. The one on the right is just out of the package, the one on the left has been soaking in gas for 8 hours. Maybe a little...
  16. Replies
    6
    Views
    766

    o-ring manifolds

    If you've ever had a problem with a leaky rubber band manifold, I found these o-rings online, and they have worked for me on my '55 and my wife's '65. The pic shows the original o-ring on the left,...
  17. Thanks Mark. Will have to recheck to prove that...

    Thanks Mark. Will have to recheck to prove that the coil is good.
  18. Thanks for responding, Eric. Yes, this is a...

    Thanks for responding, Eric. Yes, this is a generator battery system, and I do have the switch. It is a 3 position switch if you call "off" one of the positions. One of the power positions on the...
  19. switch for a 1919 H-D with battery, coil, generator

    Currently involved with trying to start this 61 inch twin, but can't get spark to the points. I have switch diagrams, and I was wondering if anyone knows the difference between a switch for a battery...
  20. Replies
    8
    Views
    1,013

    Well, the bubbles said go after I stopped a pesky...

    Well, the bubbles said go after I stopped a pesky leak at the rivet I put in the rear intake nipple. But I'm still having an issue with high idle when this bitch warms up. It has receded a little,...
  21. Replies
    8
    Views
    1,013

    And that's what the first one I got looked like....

    And that's what the first one I got looked like. The second had a better turned finish on the pipes, and the both seals were a light hand press fit on the pipes. The moral of the story is "ask and...
  22. Replies
    8
    Views
    1,013

    And I would agree with you, Jerry. The fellow at...

    And I would agree with you, Jerry. The fellow at Throttle Masters did however say when he first responded that he was having his in-house machinist measure the ones he had in stock. This may have...
  23. Replies
    8
    Views
    1,013

    My guess would be that they grab your item from...

    My guess would be that they grab your item from stock, and send it to you. If you complain, they make good so as not to tarnish their rep. We all know that the majority of these parts are shipped in...
  24. Replies
    8
    Views
    1,013

    Good service from Throttle masters

    Thought I'd let everyone know that I had a good experience with gnlemont at Throttle Masters. Bought a plumber's manifold, and when I got it, the pipe ends were out of round to the point where I...
  25. Replies
    4
    Views
    767

    Yeah, the Indian ad got by me. Thanks for the...

    Yeah, the Indian ad got by me. Thanks for the info.
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4