Search:

Type: Posts; User: DanM

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    404

    There is a company advertising in the amca mag. ...

    There is a company advertising in the amca mag. Also posts a lot of mag videos on Facebook. Appears to have equipment and knowledge.

    Vahan Dinihanian at vahan237@gmail.com
  2. Replies
    2
    Views
    102

    Hi Qtaug! The Yankee Chapter has a ride in...

    Hi Qtaug!

    The Yankee Chapter has a ride in September based out of Mohawk Park on Rt 2 in Charlemont. Email me for particulars. A y one may join us. Email me.

    Dan
    Pocketvalve@gmail.com
  3. Replies
    51
    Views
    2,390

    What impact did the scrap metal drive of WW2 have...

    What impact did the scrap metal drive of WW2 have on bikes, especially teens bike. I imagine there were some people interested in them, but the technological advances were so far reaching that by...
  4. Thread: L.A. Sleeve

    by DanM
    Replies
    14
    Views
    1,613

    We did a piece on Millennium Technologies in the...

    We did a piece on Millennium Technologies in the magazine a while back https://www.millennium-tech.net/

    They claimed to be able to put as much as .05" per wall, and then hone it with special...
  5. Replies
    0
    Views
    303

    Center Harbor Historical Society, NH

    We have been invited to display antique bikes at the Center Harbor Historical Society open house. Sat. July 13, 10am-2 pm. This is located on Rt 25b, at the west side of Lake Winnipesaukee. Great...
  6. I think the answer is just enough paint to cover....

    I think the answer is just enough paint to cover. Set a mask on the hinge and only remove for last coat of primer. Set a mask on and only remove for the last coat of paint. Same to make little...
  7. Replies
    72
    Views
    33,295

    When I launched the JD user group on Yahoo, I had...

    When I launched the JD user group on Yahoo, I had actually hoped to learn how to make a webpage. I went to the webmaster where I worked adn he said, why do that, start a Yahoo Group. We had members...
  8. Jack- My only advice is to buy complete bike. ...

    Jack-

    My only advice is to buy complete bike. Forget the price. If you start with even a HD or Indian engine, your search for the rest is a challenge. For other marques, very, very difficult. ...
  9. Replies
    6
    Views
    2,257

    Nice Job Martin. Thanks for sharing. Sorry i...

    Nice Job Martin. Thanks for sharing. Sorry i wasnt clear on the countersink for the peen. I dont know what others do for this job, but i suggest getting some kits from comp dist before they stop...
  10. Replies
    27
    Views
    6,573

    In one of my Nuts and Bolts articles we discussed...

    In one of my Nuts and Bolts articles we discussed Millenium Technologies. ://www.millennium-tech.net/serviceInfo.php?id=1

    The can plate up to .050 thick. They do hu dreds of cylinders a month. ...
  11. One of our chapter members got in touch with...

    One of our chapter members got in touch with Linda and they are both fine. I can get him your message about oiling. How can Jim contact you?
  12. Replies
    9
    Views
    3,265

    Welcome aboard!

    Welcome aboard!
  13. Replies
    5
    Views
    1,327

    Thanks Steve and Peter. I do have 1 under the...

    Thanks Steve and Peter. I do have 1 under the horn button.

    I think I will solder the plug to ensure it can't come free.
    Dan
  14. Replies
    5
    Views
    1,327

    Thanks Eric. I did mock it up without the set...

    Thanks Eric. I did mock it up without the set screw, but I am leaning towards adding one. From underneath it should be invisible.

    I have a set of bars for my '13 project, and they have the...
  15. Replies
    5
    Views
    1,327

    Setting up the control coil in handlebar

    Happy HumpDay all!

    When setting up the control coil in the handlebar, how are you handling the little spool at the grip end? After threading it onto the control coil, I can pull it into the bar...
  16. Hi Flathead... your post has a good line of...

    Hi Flathead... your post has a good line of response, except the guy doesn't want to do it and he wants to save his paint.

    I found a few places by googling, and they look good. But, I was...
  17. gas tank cleaning and sealing recommended vendors

    Can anyone make a recommendation for a supplier of tank cleaning and sealing? I have been asked, but don't have any experience with supplier of this. The gentleman that asked would like to send the...
  18. I am looking for a car moving company and saw...

    I am looking for a car moving company and saw that Horseless Carriage Transport in that NJ area has secure car parking and storage. Perhaps they will take the trailer.
    ...
  19. You may be done, but I obtained VL piston s from...

    You may be done, but I obtained VL piston s from Harbor Vintage. I recommend getting a list of available piston sizes from the supplier, then work with the machine shop to find the smallest clean...
  20. http://www.specialshapes.com/59.html Its out...

    http://www.specialshapes.com/59.html

    Its out there for crafting. I looked up tin plated steel.

    Also at the local hobby shop, or they can get it. I mentioned K&S in one of my articles for...
  21. Chad, Thank you, and for what its worth, I used...

    Chad, Thank you, and for what its worth, I used free online converter, PDF to JPG to make them small enough to post.
  22. 222392224022241 Sorry for the upside down...

    222392224022241

    Sorry for the upside down images. For some reason when I try to rotate and save, they came out the same.

    I used this process on my 1926 Harley tanks and currently on 1913. ...
  23. 2223522236222372223822234

    2223522236222372223822234
  24. Replies
    14
    Views
    4,522

    I had to get my wheel hub back incomplete after...

    I had to get my wheel hub back incomplete after an inordinate amount of time also.
  25. AMCA magazine- Nuts and Bolts article- electric start conversions

    Hello all,

    I hope you have enjoyed some of the Nuts and Bolts articles. I do appreciate the feedback people have been sending me.

    I am working on a piece about electric start conversion kits...
Results 1 to 25 of 394
Page 1 of 16 1 2 3 4