Search:

Type: Posts; User: Kozy

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Thread: Pangor Products

    by Kozy
    Replies
    13
    Views
    450

    MH steam control valve

    MH steam control valve
  2. Thread: Pangor Products

    by Kozy
    Replies
    13
    Views
    450

    Looks like the nut off the top of a control valve...

    Looks like the nut off the top of a control valve stem.
  3. Replies
    24
    Views
    1,078

    Thanks rbackpage and Jerry. I've been collecting...

    Thanks rbackpage and Jerry. I've been collecting bits to put together a 42 U sidecar rig and have both chain and 1.5 belt drives in my pile. Due to arthritic and replaced knees I'd like to use the...
  4. Replies
    24
    Views
    1,078

    Does anybody run a primary belt on a sidecar rig...

    Does anybody run a primary belt on a sidecar rig or is the weight too much for a belt?
  5. Replies
    26
    Views
    1,161

    Thanks, in the picture I attached the clip is...

    Thanks, in the picture I attached the clip is installed upside down. Used on OHV only?
  6. Replies
    26
    Views
    1,161

    On center case stud just above VIN No.

    On center case stud just above VIN No.
  7. Replies
    38
    Views
    1,678

    Thanks Hack, I'll give it a try.

    Thanks Hack, I'll give it a try.
  8. Replies
    38
    Views
    1,678

    Straight vinegar or dilute with water?

    Straight vinegar or dilute with water?
  9. Replies
    3
    Views
    366

    Palmer says 40-early 41.

    Palmer says 40-early 41.
  10. No outside grease zerks for the spring rod...

    No outside grease zerks for the spring rod bushings, no bosses for the grease zerks on the rockers and the position of the front brake cable clamp mounting screw are consistent with the '37 fork.
  11. Replies
    53
    Views
    5,408

    Look here for some insight.t...

    Look here for some insight.t http://victorylibrary.com/45MAG.htm
  12. Replies
    4
    Views
    615

    Greg, Check your inbox.

    Greg,
    Check your inbox.
  13. Replies
    53
    Views
    5,408

    How many times have you seen an ad for a model...

    How many times have you seen an ad for a model U/UL/ULH motor and fuel tanks? Some where another knuckle is born.
  14. Thanks for the info, I have experience with both...

    Thanks for the info, I have experience with both Ruby and Stay Silv. I should have thought "tinning fluid".
  15. Soldering requires absolute cleanliness. How do...

    Soldering requires absolute cleanliness. How do you go about cleaning the damaged area to ensure penetration of the molten solder?
  16. You're right and continuing with that attitude an...

    You're right and continuing with that attitude an antique could evolve into a fossil!
  17. Replies
    6
    Views
    2,036

    Thank you both

    Thank you both
  18. Replies
    6
    Views
    2,036

    Does anyone reproduce the glass lens for this...

    Does anyone reproduce the glass lens for this light?
  19. Replies
    10
    Views
    4,962

    The bracket the stand leg fits into may be for a...

    The bracket the stand leg fits into may be for a rigid frame.
  20. Replies
    20
    Views
    7,126

    Should the spool be soldered to the cable casing?

    Should the spool be soldered to the cable casing?
  21. Replies
    25
    Views
    9,384

    Is Brooks leather any good? At one time it was...

    Is Brooks leather any good? At one time it was the thing to have here in Michigan. I don't have any experience with Schott leather but have their down filled hunting gear from the 70's and it has...
  22. Thread: Steering damper

    by Kozy
    Replies
    5
    Views
    2,488

    After soaking in oil and cutting the end off put...

    After soaking in oil and cutting the end off put it in a hydraulic press and push it out.
  23. Replies
    16
    Views
    6,530

    Millwrights have been using the shim type shown...

    Millwrights have been using the shim type shown in the ebay listing to align coupled shafts for years. They're available from industrial suppliers like McMaster-Carr for about a buck apiece.
  24. Replies
    17
    Views
    11,437

    Has S&S given up on BT flathead cylinders and...

    Has S&S given up on BT flathead cylinders and heads?
  25. Jerry, Thanks for the reply and photos. I didn't...

    Jerry, Thanks for the reply and photos. I didn't realize there were differences in the shape of the main brace. You have a great eye for detail.
Results 1 to 25 of 72
Page 1 of 3 1 2 3