Search:

Type: Posts; User: tomfiii

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    339

    Check with Mike at Kiwi to see if he has the...

    Check with Mike at Kiwi to see if he has the correct tension spring and old style disc in stock.
  2. Replies
    45
    Views
    5,418

    The foot traffic was definitely less on Thurs.&...

    The foot traffic was definitely less on Thurs.& Fri.then previous year.
  3. Replies
    45
    Views
    5,418

    A more official type notice "earlier" would have...

    A more official type notice "earlier" would have been appreciated.
  4. Replies
    9
    Views
    1,363

    I would look at shaft movement and the rubbing...

    I would look at shaft movement and the rubbing block for wear.
  5. Replies
    8
    Views
    801

    If the powder coat was done right the the bead...

    If the powder coat was done right the the bead blaster will leave a nice patina on powder coat.
  6. How are you measuring rings, end gap ? feeler...

    How are you measuring rings, end gap ? feeler gage ? Are you checking compression with carb WOT?
  7. Replies
    9
    Views
    1,203

    Dusty Dog, That was for the good anti rattle...

    Dusty Dog, That was for the good anti rattle spring that rested on axle.

    Some years used different pistons ,as the front had a retraction spring built onto piston, that one could develop a squeal...
  8. Replies
    3
    Views
    654

    Sorry must have looked askew at it. Parts book...

    Sorry must have looked askew at it. Parts book has dimensions in back.
  9. Replies
    12
    Views
    1,367

    Note: Indian's color in wiring diagrams was for...

    Note: Indian's color in wiring diagrams was for tracer color and not color of wire. Also different years used different tracer patterns.
  10. Replies
    3
    Views
    654

    Early '47 type or later front drive speedo? Look...

    Early '47 type or later front drive speedo? Look at Greer's site for dimensions.
  11. Replies
    12
    Views
    1,367

    Good place to get correct color wire with correct...

    Good place to get correct color wire with correct tracer color and they will loom it also.
  12. Replies
    6
    Views
    1,209

    Iwould leave them in if clearance ok,but take to...

    Iwould leave them in if clearance ok,but take to competent welder to check out. The rocker shafts Need inspection closely.
  13. Replies
    12
    Views
    4,900

    As far as I've looked the sleeve comes from the...

    As far as I've looked the sleeve comes from the bars down to the instrument cover and then uses another cover to the front end from there. Horn wire goes towards ign. switch and then down frame to...
  14. Replies
    28
    Views
    9,845

    An intermediate support should be added if you...

    An intermediate support should be added if you haven't already done so.
  15. Use high gear for rocking it back and forth.

    Use high gear for rocking it back and forth.
  16. Replies
    3
    Views
    938

    Is the tight spot the same with bottom off? Wear...

    Is the tight spot the same with bottom off? Wear spots on bottom? Pump can have a tight spot sometimes if gears were removed and the running faces are not matched.
  17. Replies
    46
    Views
    9,183

    Hope they get their new camping regulations out...

    Hope they get their new camping regulations out so we can make adjustments.
  18. Replies
    4
    Views
    1,770

    description Greer ...

    description Greer https://www.jerrygreersengineering.com/part_view.php?part_id=8234&y=1945&m=Chief&p_group_id=0120CHF44-47
  19. Replies
    30
    Views
    8,768

    Did you change coil to 12v or put thermister in...

    Did you change coil to 12v or put thermister in line with.
  20. Replies
    15
    Views
    3,108

    Did it not have the timing hole plug just above...

    Did it not have the timing hole plug just above the drain plug,they look the same?
  21. Replies
    15
    Views
    3,108

    That would be heads,pistons,carb,cam...

    That would be heads,pistons,carb,cam followers,magneto and sometimes guides.
  22. Replies
    7
    Views
    2,068

    They are referring to motorcycle oil not 2 stroke...

    They are referring to motorcycle oil not 2 stroke oil. Friends Cleveland said 60 w oil for mix so carburetor would work properly, yours could be a different viscosity.
  23. Replies
    1
    Views
    802

    That hole is end cap of baffle in muffler, I have...

    That hole is end cap of baffle in muffler, I have used a 3/16" drill end drilled several holes around center hole for flow.
  24. Replies
    5
    Views
    1,783

    When using mismatched flywheels you should find a...

    When using mismatched flywheels you should find a balancer who will balance each flywheel separately first ,then the assembly.
  25. Thread: 48 gas filter

    by tomfiii
    Replies
    2
    Views
    910

    Th e filter is black and the bale assembly is cad.

    Th e filter is black and the bale assembly is cad.
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4