Search:

Type: Posts; User: tomfiii

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    625

    I use "Break Free" lubricant on cables.

    I use "Break Free" lubricant on cables.
  2. Replies
    16
    Views
    625

    Should have explained swap better. As for the...

    Should have explained swap better. As for the wires first rotate the block pin and wire 180 degrees and see if it moves easier ,if not then new control wire, and they have a set also and may need to...
  3. Replies
    16
    Views
    625

    If it's a distributor model all that needs to be...

    If it's a distributor model all that needs to be done is swap control cables side for side.
  4. Replies
    11
    Views
    468

    Make sure no paint or powder coat is on surfaces....

    Make sure no paint or powder coat is on surfaces. Mike at Kiwi has proper spring and may still have some original material friction pad in stock.
  5. Covering the cost, is that something the National...

    Covering the cost, is that something the National could do? Everyone should carry "accessible" contact information and medical alert info no matter where they go. Most of our events are not close...
  6. Replies
    11
    Views
    710

    I've used a 6 volt battery that fits a BMW in my...

    I've used a 6 volt battery that fits a BMW in my gutted shell, pretty sure it'll fit the Starklite shell.
  7. Thread: Oil change

    by tomfiii
    Replies
    15
    Views
    1,302

    I got Lucas 50w motorcycle oil at a decent price...

    I got Lucas 50w motorcycle oil at a decent price thru Summit Racing.
  8. Replies
    17
    Views
    1,584

    https://www.marylandvolunteer.org/department/upper...

    https://www.marylandvolunteer.org/department/upperco-volunteer-fire-company/
    Entrance to field use Carnival Av. Field between railroad tracks and Carnival Av. and off to right of Carnival...
  9. Thread: Oil change

    by tomfiii
    Replies
    15
    Views
    1,302

    Removing check ball was only recommended for...

    Removing check ball was only recommended for N.Y/police bikes for winter. Remember the oil in tank does not run that hot so multi grade entering motor may not shift to higher weight in a timely...
  10. Replies
    13
    Views
    965

    I use a dash of star-tron every tank or so and...

    I use a dash of star-tron every tank or so and also Blenzall, but if going to sit for awhile then stabil additive. Just try to use the right tank enough to rotate gas.
  11. Replies
    12
    Views
    946

    Hot start check coil, it could have a heat soak...

    Hot start check coil, it could have a heat soak problem. Also make sure you don't have peaks forming on points as condenser could cause that.
  12. Replies
    66
    Views
    4,003

    Sometimes hard kicking can mean kicker needs a...

    Sometimes hard kicking can mean kicker needs a shot of grease.
  13. Replies
    5
    Views
    652

    Check with Mike at Kiwi to see if he has the...

    Check with Mike at Kiwi to see if he has the correct tension spring and old style disc in stock.
  14. Replies
    45
    Views
    7,102

    The foot traffic was definitely less on Thurs.&...

    The foot traffic was definitely less on Thurs.& Fri.then previous year.
  15. Replies
    45
    Views
    7,102

    A more official type notice "earlier" would have...

    A more official type notice "earlier" would have been appreciated.
  16. Replies
    10
    Views
    2,322

    I would look at shaft movement and the rubbing...

    I would look at shaft movement and the rubbing block for wear.
  17. Replies
    8
    Views
    1,009

    If the powder coat was done right the the bead...

    If the powder coat was done right the the bead blaster will leave a nice patina on powder coat.
  18. How are you measuring rings, end gap ? feeler...

    How are you measuring rings, end gap ? feeler gage ? Are you checking compression with carb WOT?
  19. Replies
    9
    Views
    1,735

    Dusty Dog, That was for the good anti rattle...

    Dusty Dog, That was for the good anti rattle spring that rested on axle.

    Some years used different pistons ,as the front had a retraction spring built onto piston, that one could develop a squeal...
  20. Replies
    3
    Views
    837

    Sorry must have looked askew at it. Parts book...

    Sorry must have looked askew at it. Parts book has dimensions in back.
  21. Replies
    12
    Views
    1,724

    Note: Indian's color in wiring diagrams was for...

    Note: Indian's color in wiring diagrams was for tracer color and not color of wire. Also different years used different tracer patterns.
  22. Replies
    3
    Views
    837

    Early '47 type or later front drive speedo? Look...

    Early '47 type or later front drive speedo? Look at Greer's site for dimensions.
  23. Replies
    12
    Views
    1,724

    Good place to get correct color wire with correct...

    Good place to get correct color wire with correct tracer color and they will loom it also.
  24. Replies
    6
    Views
    1,386

    Iwould leave them in if clearance ok,but take to...

    Iwould leave them in if clearance ok,but take to competent welder to check out. The rocker shafts Need inspection closely.
  25. Replies
    12
    Views
    5,295

    As far as I've looked the sleeve comes from the...

    As far as I've looked the sleeve comes from the bars down to the instrument cover and then uses another cover to the front end from there. Horn wire goes towards ign. switch and then down frame to...
Results 1 to 25 of 177
Page 1 of 8 1 2 3 4