Search:

Type: Posts; User: BigLakeBob

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    338

    25895This is the tool I made. 3/8" dia with a...

    25895This is the tool I made. 3/8" dia with a 3/16" wide flat area to avoid hitting the rolled edge of the board. I got carried away, heat treated mine then black oxide.
  2. Replies
    15
    Views
    802

    That's so cool Doug does that, that man has been...

    That's so cool Doug does that, that man has been around. Thanks for the link. Bob
  3. Replies
    10
    Views
    338

    The saddlebag tool does work really well, got...

    The saddlebag tool does work really well, got mine off ebay, Kent Moore # HD-39787-A. I got a new one for $50. They are on there quite often. I made a tool for the split rivets,...
  4. Replies
    12
    Views
    492

    Len, How thick are the leather ones? Does the...

    Len, How thick are the leather ones? Does the smooth or rough side of the leather go against the tank?



    Eric, How thick are the cork ones?

    Thanks.
  5. Replies
    12
    Views
    492

    The 'Viton' gaskets I have I purchased at Wauseon...

    The 'Viton' gaskets I have I purchased at Wauseon from a vendor about 4 years ago. I cannot verify they are Viton but I would want to think I bought what I was told. The gaskets were black. As...
  6. Replies
    12
    Views
    492

    Gas Cap Gaskets

    Just wondered what material everyone is having the best luck with, with today's fuel? I recently got another bike up and running and decided to try Viton, it swelled up more than the Buna that is in...
  7. I saw a video from Dale Walksler, I believe,...

    I saw a video from Dale Walksler, I believe, where he heats the entire engine on a hot plate before disassembling anything. Says he gets alot better results.
  8. Replies
    17
    Views
    1,008

    A couple of years ago I altered a generator...

    A couple of years ago I altered a generator bottom shovel inner primary to fit a '57FL bottom end for a friend so he could have electric start. I circle milled (milled the outside of the primary to...
  9. You mention all mechanical, how is everything in...

    You mention all mechanical, how is everything in the electric circuit? Battery fully charged, gen polarized and not shorted, any key switch shorts, condenser correct and good? Are the plugs wet or...
  10. Replies
    6
    Views
    457

    Great info on the Ace switch, Thanks Gerry.

    Great info on the Ace switch, Thanks Gerry.
  11. Replies
    45
    Views
    6,034

    I find the Walmart thing pretty funny if at all...

    I find the Walmart thing pretty funny if at all true. The meet starts Friday, but as is the new norm, the great volunteer chapter members usually allow non vendors (shoppers) in the day prior during...
  12. Replies
    11
    Views
    2,739

    Maybe 1 & 5/64 (69/64")?

    Maybe 1 & 5/64 (69/64")?
  13. Replies
    42
    Views
    4,295

    Looking through the 'The Antique Motorcycle'...

    Looking through the 'The Antique Motorcycle' magazine winter 1995 and found this which is some additional info for some of the above mentioned models.251422514325144
  14. Replies
    42
    Views
    4,295

    I had a late sixty's Evinrude boat motor. It was...

    I had a late sixty's Evinrude boat motor. It was called the Sportster and the throttle grip was the same style as used on '62-'64 HD's.
  15. Replies
    7
    Views
    816

    What year/ style pan heads?

    What year/ style pan heads?
  16. Thread: Uno wheel

    by BigLakeBob
    Replies
    5
    Views
    853

    Uno wheel

    http://theoldmotor.com/?p=147211

    Does anyone have more info?
  17. Thread: Dave Carter

    by BigLakeBob
    Replies
    0
    Views
    586

    Dave Carter

    You need to clear some messages out of your in and/or sent boxes so I can reply to your PM. Thanks, Bob
  18. Replies
    4
    Views
    812

    Also, Tedd's cups were not as hard as original, I...

    Also, Tedd's cups were not as hard as original, I was able to cut the race with a lathe tool to adjust the above mentioned stack height.2475524756
    Just to clarify, the orig race was 64Rc and Tedd's...
  19. Replies
    20
    Views
    2,940

    Pretty straight in a row with not crooked digits...

    Pretty straight in a row with not crooked digits also.
  20. Thread: new guy

    by BigLakeBob
    Replies
    4
    Views
    1,040

    Hi Ken, welcome to the forum. I rode a pan...

    Hi Ken, welcome to the forum. I rode a pan chopper for years and still love choppers but lower back issues keep me on a bike with suspension now. I think there are a lot of previous chopper people...
  21. Replies
    0
    Views
    504

    Gas Tank Identification help

    I picked these tanks up in a thrift store yesterday. The tabs and welds look HD to me and not aftermarket? They are 3 1/2 gal. With the style of petcock ('75 newer?)) what years and model would...
  22. Replies
    15
    Views
    2,334

    2442724428I ran a seat similar to that on my '69,...

    2442724428I ran a seat similar to that on my '69, instead of drilling a hole in the fender I made the bracket shown from aluminum angle. It has felt on the bottom and attached to the luggage rack. ...
  23. Are you advancing the cam when you check timing?

    Are you advancing the cam when you check timing?
  24. Here is a OEM set with instructions.2433924340

    Here is a OEM set with instructions.2433924340
  25. Replies
    11
    Views
    1,027

    24312 Here is the service bulletin.

    24312
    Here is the service bulletin.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4