Search:

Type: Posts; User: underwel

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    203

    Help Identifying Motorcycle

    26497This photo was taken of my grandpa in 1944 when he was 18. Not a great picture and a lot of the bike is covered up but I was wondering if anyone had a clue as to what exactly it was. My...
  2. I went through the same thing about 5 years ago. ...

    I went through the same thing about 5 years ago. I am definitely no expert, but I can give you a few of my lessons learned. I bought a civilianized 45 flathead and did a complete rebuild. First...
  3. Replies
    19
    Views
    1,788

    Thanks so much for the advice!

    Thanks so much for the advice!
  4. Replies
    19
    Views
    1,788

    Thanks everyone for all the comments. I...

    Thanks everyone for all the comments. I contacted Roeder (about 2 hour drive from me), they said they could do it. Hoping to take the engine up there in December.
  5. Replies
    22
    Views
    1,500

    Thanks so much for the information!! That would...

    Thanks so much for the information!! That would definitely make sense of why the front mounts broke
  6. Replies
    22
    Views
    1,500

    C2K I think you are right about the motor...

    C2K
    I think you are right about the motor mounts. I am assuming that someone should have shimmed the front mounts. They are both broken on the engine. I think I'm going to leave it pretty much...
  7. Replies
    22
    Views
    1,500

    2624626247262482624926250 From the casting...

    2624626247262482624926250

    From the casting numbers the frame I believe is 1948, plus it does not have the horn mounts as the horn would have been mounted on the springer. I'm pretty sure the...
  8. Replies
    22
    Views
    1,500

    Thanks Eric, I appreciate your response. I'm...

    Thanks Eric,
    I appreciate your response. I'm kinda with you, I like the fact that the bike was done in the sixties. I think my plan is to have the engine rebuilt and just clean it up a bit. If I...
  9. Replies
    22
    Views
    1,500

    Like fender trim? There wasn't any left on it.

    Like fender trim? There wasn't any left on it.
  10. Replies
    22
    Views
    1,500

    1948/1949 Panhead

    Just for conversation. I've picked up an old bobber project that I've posted a few things about. I found it in a co-worker's dads barn. Its been sitting in there since the late 1960's. I always...
  11. Replies
    19
    Views
    1,788

    Not sure why the pictures rotated sideways

    Not sure why the pictures rotated sideways
  12. Replies
    19
    Views
    1,788

    26189261902618726188

    26189261902618726188
  13. Replies
    19
    Views
    1,788

    2618426186

    2618426186
  14. Replies
    19
    Views
    1,788

    47 Knucklehead broken front motor mounts

    Good Morning,
    I have a 47 FL Knucklehead engine with both front motor mounts missing some chunks. Does anyone know a shop in Ohio that could repair these?
    Thanks,
    Eric
  15. Replies
    20
    Views
    2,504

    Hack, What are those? Where would I find some?

    Hack,
    What are those? Where would I find some?
  16. Replies
    20
    Views
    2,504

    Thanks everyone for the Advice!

    Thanks everyone for the Advice!
  17. Replies
    20
    Views
    2,504

    Current setup

    Current setup
  18. Replies
    20
    Views
    2,504

    The bike has a stock hydra glide front end with...

    The bike has a stock hydra glide front end with 16" rims. I may be limited to the squash pipe.
  19. Replies
    20
    Views
    2,504

    Bobber exhaust ideas

    I just bought a bobber project that was starting, I'm guessing, in the 1960s. An old guy bought it in the late 1960s and basically just rolled it in his garage where it has sat since at least 1969. ...
  20. Replies
    18
    Views
    9,928

    For the Ride Control? If so, I have that on it. ...

    For the Ride Control? If so, I have that on it. I'm starting to think I might have a tire issue. Thanks you for responding!
  21. Replies
    18
    Views
    9,928

    I know this is an old thread, but I was wondering...

    I know this is an old thread, but I was wondering if the problem got solved? I have the exact same problem with my 42 WLA. I'm trying to figure out if it is the Springer, the wheel, or the tire. ...
  22. Replies
    8
    Views
    1,357

    Belly numbers do not match. VIN side is 47, right...

    Belly numbers do not match. VIN side is 47, right side is 41. Iím also in Ohio so titling would get interesting
  23. Replies
    8
    Views
    1,357

    Thanks for that! Hopefully it comes in handy.

    Thanks for that! Hopefully it comes in handy.
  24. Replies
    8
    Views
    1,357

    Thanks for the response. I've seen a picture of...

    Thanks for the response. I've seen a picture of the engine number, looks good. I haven't seen the belly numbers yet. I'm hoping to make it out in a couple weeks and look it over. Hopefully the...
  25. Replies
    8
    Views
    1,357

    Need help making an offer, 1947 Knucklehead

    Good Morning,
    Not sure if this is where to ask for advice, but I will give it a try. I have found a 1947 knucklehead engine, no title, looks rough but turns, sitting on a 1949 panhead rolling...
Results 1 to 25 of 29
Page 1 of 2 1 2