Search:

Type: Posts; User: 46CHF

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    18
    Views
    540

    That’s a good question Cotten what are your...

    That’s a good question Cotten what are your thoughts on insulation or heat transfer
  2. Replies
    18
    Views
    540

    Knuckle head gaskets

    What are thoughts on using copper head gaskets on 74 knuckle motor
  3. Thread: 45 modifications

    by 46CHF
    Replies
    0
    Views
    386

    45 modifications

    Can 74 panhead plumbers nipples be installed in 45 jugs and if so what is the internal thread size /small dia. End of big twin nipple.
  4. Replies
    8
    Views
    7,451

    Autolite 303 . I have 2 40’s chiefs that r both...

    Autolite 303 . I have 2 40’s chiefs that r both daily riders that I have been running those plugs for going on 20 plus years
  5. Replies
    66
    Views
    3,977

    Remove top crankcase plug ( 1/8 pipe plug)from...

    Remove top crankcase plug ( 1/8 pipe plug)from lower left hand crankcase excess oil will drain out once it quits dripping put plug back In you are ready to roll
  6. Sounds like wet sump drain oil in cases and...

    Sounds like wet sump drain oil in cases and refill with tank pump
  7. Replies
    58
    Views
    37,224

    Now thats funny

    Now thats funny
  8. Replies
    8
    Views
    1,406

    I have run both and and they seem to handle the...

    I have run both and and they seem to handle the same ,I have put dozens of the shinkos on vintage machines and had no complaints and the price is half of the other brand. Mileage seems the same with...
  9. Thread: Checking timing

    by 46CHF
    Replies
    35
    Views
    7,655

    What model r u talking of

    What model r u talking of
  10. Thread: 45 jugs

    by 46CHF
    Replies
    1
    Views
    534

    45 jugs

    Can 45 jugs with 3/8 studs for iron heads be modified to accept aluminum heads
  11. Replies
    5
    Views
    2,675

    I am looking for a set of .020 bonneville pistone

    I am looking for a set of .020 bonneville pistone
  12. Replies
    10
    Views
    3,055

    I put studs in very set of heads I build and have...

    I put studs in very set of heads I build and have never had an issue
  13. Replies
    1
    Views
    837

    Bonneville pistons

    Looking for a set of 74 bonneville pistons +.020
  14. Thread: Panhead Tires

    by 46CHF
    Replies
    14
    Views
    4,383

    Shinko 240s are the speed grip pattern used by...

    Shinko 240s are the speed grip pattern used by harley-Davidson after 1968. They can be a little squirrely on grooved pavement and iron grate bridges I prefer the 270 supereagle pattern. They are a...
  15. Thread: Panhead Tires

    by 46CHF
    Replies
    14
    Views
    4,383

    I have put Shinko 270s on lots of pans and...

    I have put Shinko 270s on lots of pans and shovels. They are a replica Goodyear supereagle pattern which was used by Harley Davidson till 1968. Have not had any problems and run them on my own bikes
  16. Replies
    5
    Views
    2,453

    Truett & Osborn wheels the only way to go

    Truett & Osborn wheels the only way to go
  17. Replies
    0
    Views
    1,278

    78 shovel pinion shaft

    The 1/4 -20 threaded hole
    In small end of pinion. Can that just be left empty or does it need to metered down and if so to what size
    The oil feeds thru the end of this pinion not the side as...
  18. Replies
    10
    Views
    5,007

    Thanks mark, how about the clutch shaft finish...

    Thanks mark, how about the clutch shaft finish that goes across the top cover of 15 tranny parkerized ??? Matt Walksler also said you may be able to help with bearing numbers for the left and right...
  19. Replies
    10
    Views
    5,007

    Thanks mark for the info , do u have any info...

    Thanks mark for the info , do u have any info regarding valve stem clearances
  20. Replies
    10
    Views
    5,007

    Finishes for j/jd tranny

    I am currently restoring a 1915 tranny would like to know what the proper finishes would be for the case side and top covers and hardware. Can anyone help here.
  21. Replies
    0
    Views
    1,078

    J/jd valve clearance specs.

    Rebuilding 1915 61 inch top end what kind of valve stem clearances are run on these motors and on the stepped exhaust valve stems are both diameters sized or is the larger diameter just clearance...
  22. Thread: Honda model A

    by 46CHF
    Replies
    1
    Views
    2,516

    Honda model A

    Looking for any info on model A Honda bicycle motors
    Production numbers ,years manufactured vin number identification etc. also any motor drawings pictures etc.
  23. Replies
    3
    Views
    1,897

    Thanks John I will check out Stuart at jd jugs ....

    Thanks John I will check out Stuart at jd jugs . I was hoping to find a standard guide that could be modified to work
  24. Replies
    3
    Views
    1,897

    Model j valve guide question

    In the process of reworking a set of 1915 j jugs. The exhaust valve guide are already around .330 before honing true. Is anyone replacing guides with sleeves or modified guides . Any help here would...
  25. Replies
    2
    Views
    1,184

    724-561-5364

    724-561-5364
Results 1 to 25 of 53
Page 1 of 3 1 2 3