Search:

Type: Posts; User: sieber60

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    695

    67 Shovelhead 4 Speed

    Does anyone know if there is a tool made to install a main drive gear shaft seal for 67 4 speed, as you know this is a small seal and difficult to get started straight. ? Or any advise on installing...
  2. Replies
    4
    Views
    653

    Okay.. I currently have a 23 tooth compensator...

    Okay.. I currently have a 23 tooth compensator sprocket and a 22 tooth transmission sprocket and a stock rear drum brake sprocket .. 51 I think. What would change if I used a 22 tooth compensator...
  3. Replies
    4
    Views
    653

    1967 Compensator Nut

    Is the compensator nut left or right thread on a 67' FLH? Manual doesn't say. Appreciate the info. as always!

    Thanks
  4. Replies
    0
    Views
    303

    1971 Suzuki T-250

    Okay, found this 1971 Suzuki T250 and is really original, has been sitting for about ten years. I am an old Harley guy but this project looks interesting. Motor is frozen and the front forks are...
  5. Thread: Pre 69" Cases

    by sieber60
    Replies
    10
    Views
    1,649

    I appreciate the info. I've been trying to...

    I appreciate the info. I've been trying to educate my self since there are so many counterfeits out there.

    John
  6. Thread: Pre 69" Cases

    by sieber60
    Replies
    10
    Views
    1,649

    Pre 69" Cases

    So... pre 69" Harley factory would sell you a set of replacement cases. This is my understanding anyway. If so, did those cases have belly numbers? or just blank cases?

    Thanks!
  7. Replies
    5
    Views
    1,056

    Thank you all for your input. It confirms my...

    Thank you all for your input. It confirms my thoughts.
  8. Replies
    5
    Views
    1,056

    Haven't attached picture here before, hope it...

    Haven't attached picture here before, hope it works.
  9. Replies
    5
    Views
    1,056

    57 Panhead VIN

    Saw a bike on craigslist for sale. Its supposed to be 57 cases, has a shovel top end. When I asked the guy if the belly numbers matched he said he didn't see any... that was a red flag for me. My...
  10. Replies
    2
    Views
    1,146

    67 Shovelhead Rear Brake

    Can someone tell me what type of washer is used on the outer block that the banjo bolt goes through to the wheel cylinder on the rear drum brake of a 67 Shovelhead? I used copper but it wanted to...
  11. Replies
    4
    Views
    2,832

    Thank you for the reply.

    Thank you for the reply.
  12. Replies
    4
    Views
    2,832

    Shovelhead Vin

    Does anyone know if Harley in the 80's put any VIN #'s on the left case? I was looking at an 84 superglide yesterday and the motor didn't have the VIN in the usual place... There was a number on the...
  13. Replies
    4
    Views
    2,876

    One more question if anyone knows.On the 72...

    One more question if anyone knows.On the 72 Harley swingarm frame does the Vin # on the frame read from the bottom up or from the top down? Thanks
  14. Replies
    4
    Views
    2,876

    The guy that owned the frame died over 10 years...

    The guy that owned the frame died over 10 years ago... no title. The VIN is *2CxxxxxH2* had the numbers ran and they are clean. I suspect that the neck was changed or the back half was changed for...
  15. Replies
    4
    Views
    2,876

    72 FX Shovelhead Frame

    Looking at a 1972 FX Shovelhead frame. The numbers look good or correct anyway for the FX but there are two things that don't look correct on the back half. It has the rectangle blocks on each side...
  16. Replies
    1
    Views
    2,023

    Shovelhead Cylinder Heads

    Looking for informatiuon about Shovelhead heads. What are the pros and cons of early shovel heads vs later shovel heads. Any info would be greatly appreciated.

    Thanks
    Sieber60
  17. Replies
    12
    Views
    5,837

    Thanks for the info, I will contact him.

    Thanks for the info, I will contact him.
  18. Replies
    12
    Views
    5,837

    Where can a person get the part to convert. ...

    Where can a person get the part to convert.
    Thanks
  19. Replies
    12
    Views
    5,837

    Where can a person get the part to convert. ...

    Where can a person get the part to convert.
    Thanks
  20. Replies
    1
    Views
    2,482

    67 FLH Frame Casting Numbers

    I am a new member in the last year and have I have a question that I hope someone can help me with. I have a unrestored 67 FLH and I am looking at a 59 frame to start a new project. I have been...
Results 1 to 20 of 20