Search:

Type: Posts; User: Hack

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    1,517

    I scored a NOS set of MCM upsweeps a few years...

    I scored a NOS set of MCM upsweeps a few years ago, both header pipes, squeeze pipe and the lower pipe off the S pipe. Paugcho makes a similar set up. The mufflers are NOS Superior Megaphones, and...
  2. Replies
    20
    Views
    1,517

    Hearing protection required. 25683

    Hearing protection required.

    25683
  3. Replies
    6
    Views
    577

    Thanks guys. I don't have a lathe or truing stand...

    Thanks guys. I don't have a lathe or truing stand as I normally send this type of work to a shop equipped to recondition and fit the parts as needed. The little ding on the nut side going into the...
  4. Replies
    6
    Views
    577

    UL Flywheel taper servicing

    I have a set of UL wheels and the pinion taper and keyway are damaged. I was told the wheels are serviceable, not so sure now. Any EXPERT advise would be appreciated. I sold these and the guy...
  5. Thread: Pre 69" Cases

    by Hack
    Replies
    10
    Views
    1,541

    A similar case is a friend of mine moved from...

    A similar case is a friend of mine moved from Colorado to San Luis Obispo to go to Cal Poly in about 1975 or so and brought his 57 Pan chopper with him. It had factory replacement cases as his...
  6. Replies
    15
    Views
    1,844

    I grabbed some of these from Bills. Knurled on...

    I grabbed some of these from Bills. Knurled on one side with a taper on the other. The parts book shows it at the bottom of the assembly.
  7. Replies
    5
    Views
    953

    Thanks for the input guys, yeah there is enough...

    Thanks for the input guys, yeah there is enough suspicious stuff going on to make me wonder too, but not enough to verify. Next month or so I'll be ready to rebuild it and will find out for sure what...
  8. Replies
    5
    Views
    953

    Mystery numbers on FL flywheel edge?

    Are these numbers of any significance? The wheels in this 50 FL I just acquired appear to be OEM as far as I can tell without splitting the case, however it was built with an S&S rod set. Last time...
  9. Replies
    29
    Views
    6,746

    here you go. 55 pan frame, looks nice. ...

    here you go. 55 pan frame, looks nice.
    ...
  10. Replies
    17
    Views
    3,306

    Here you go Greg. 230942309523096

    Here you go Greg.

    230942309523096
  11. Replies
    11
    Views
    3,713

    I have this one in the c22943an with what looks...

    I have this one in the c22943an with what looks to be an earlier part number.
  12. Replies
    10
    Views
    2,911

    My 49 Fl registration shows; Date first sold...

    My 49 Fl registration shows; Date first sold 1949. Next to that under Make; HARDA, yr. 1954: yr model 1949. The DRF number was stamped on the original HD frame, not the engine (original cases) and...
  13. Replies
    9
    Views
    2,168

    My 49 Pan does the same thing and I have been...

    My 49 Pan does the same thing and I have been riding it that way since I got it in 1972. A wise engine rebuilder in Santa Barbara where I was living at the time hipped me to the notion that pressure...
  14. Replies
    6
    Views
    3,343

    I bought a nice looking set of Glide risers...

    I bought a nice looking set of Glide risers listed as "OEM Original removed from a stock 53 Panhead". They were Taiwan Ted crap, I knew I was screwed as soon as I picked up the box. I got a refund...
  15. Replies
    4
    Views
    2,437

    Thanks to all... Heat and a good twist did the...

    Thanks to all... Heat and a good twist did the job without incident. Threads are all good and you can see a too long replacement plug was indeed used on the one side.

    17906
  16. Replies
    4
    Views
    2,437

    Early Glide Slider Drain Plug Dilemma

    I just scored a nice set of Glide sliders. One drain plug is stuck, stuck, stuck. The other only turns in about 1.5 turns and no more. Any ideas about getting the stuck one out without taking...
  17. Replies
    2
    Views
    1,500

    Try hdpaint.tk

    Try hdpaint.tk
  18. Have you tried calling this shop in near by Grand...

    Have you tried calling this shop in near by Grand Rapids??
    Harry's Cycles
    Motorcycle Shop
    Address: 2457 Gaynor Ave NW, Grand Rapids, MI 49544
    Phone:(616) 570-6114
  19. Thread: Frame Lock

    by Hack
    Replies
    21
    Views
    5,908

    1948 Frame Lock

    Has anyone ever removed a lock intact? The lock in my 48 frame is frozen, not sure if it is the plunger, lock or both. I really would like to remove it intact if possible for repair, again if...
  20. Thread: 1941 trans case

    by Hack
    Replies
    21
    Views
    7,779

    I have a trans Dated L 9 with a milled&drilled...

    I have a trans Dated L 9 with a milled&drilled vent boss a lonely 1 to the right. The adjuster boss is stamped with the mystery 40 quite clearly but with a T above it and a sideways F that is at the...
Results 1 to 20 of 20