Search:

Type: Posts; User: aumick10

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    110

    I think your OEM pt no is 9875. Wire terminal...

    I think your OEM pt no is 9875.
    Wire terminal female spade type, 5/16" slot-16-22 g wire.
    Terminal no 9913 is similiar but for 14-16 g wire.

    This looks like an uninsulated terminal in the parts...
  2. Replies
    18
    Views
    1,820

    A small bearing separator will do the same job....

    A small bearing separator will do the same job. It will have just enough room to grip the bearing inner race.
    Sit the seperator on a vice with the sprocket end up and sprocket nut installed.
    Give...
  3. Replies
    4
    Views
    110

    Spade connectors are typically available in 1/4"...

    Spade connectors are typically available in 1/4" wide and 3/8" wide. I have only seen the 3/8" connectors available for 12-10 gauge wires, yellow insulators.
    These yellow ones are bigger than your...
  4. Replies
    59
    Views
    5,627

    My 29 JD is up and running, almost ready to road...

    My 29 JD is up and running, almost ready to road test.
    Still some OEM parts to chase up if I can find them.I have a complete OEM 1929 front guard and valances, but it needs some major surgery.
    I...
  5. Replies
    30
    Views
    4,535

    Saves that precious time.

    Saves that precious time.
  6. Replies
    30
    Views
    4,535

    I will stab myself in the eye first, then figure...

    I will stab myself in the eye first, then figure out how to get some machining done.
    Cheers
  7. Replies
    30
    Views
    4,535

    If you are supplying these as a service, that is...

    If you are supplying these as a service, that is the type of thing you need to do.

    I have a DLX66 that needs some work. How is your work load?
    Cheers
  8. Replies
    30
    Views
    4,535

    I just put the shaft in some soft jaws and took...

    I just put the shaft in some soft jaws and took it gently.
    Used a small ball peen hammer, taped the cam on and peened over the shaft.
    I filed the shaft OD and flat down by hand.

    Once again, I...
  9. Replies
    30
    Views
    4,535

    Getting the flat on the shaft in the correct...

    Getting the flat on the shaft in the correct orientation was the hardest part, not going for originality, the peen was just hit it with a hammer over and over again.
  10. Replies
    30
    Views
    4,535

    Tom, It was more an exercise in desperation than...

    Tom,
    It was more an exercise in desperation than anything else.

    I couldn't find the correct shaft, so I used what I could get and had in stock.
    Schebler throttle shaft, Linkert lift cam, correct...
  11. Replies
    30
    Views
    4,535

    Marc, I recently had to make a choke shaft for a...

    Marc,
    I recently had to make a choke shaft for a DLX38 and only had a long spring.
    Snipped of a coil or two and it now works fine.
    Cheers
  12. Replies
    9
    Views
    577

    Doesn't that turn the thingyabob.

    Doesn't that turn the thingyabob.
  13. Replies
    9
    Views
    577

    Mark, I think that is a 34453-52 shifter shaft....

    Mark,
    I think that is a 34453-52 shifter shaft.
    52 to early 79, Foot shift 4 speed, foot shift, some 1980 models.
    Cheers
  14. Replies
    5
    Views
    252

    Last time I did this was with a laser I had. It...

    Last time I did this was with a laser I had. It was attached to a cheap spirit level someone gave me.

    Set it up a few inches above the floor with the laser touching the rear tire at the two widest...
  15. Replies
    27
    Views
    4,031

    If the barrel will rotate from the locked to...

    If the barrel will rotate from the locked to unlocked position, this part is obviously not seized.

    I am not familiar with these locks but if the barrel rotates, in theory it should be possible to...
  16. Replies
    27
    Views
    4,031

    Not specific to your bike, and probably won't...

    Not specific to your bike, and probably won't help you now, but I have always used graphite powder only on any locks.
  17. Replies
    225
    Views
    25,761

    They actually sent me two different dampers that...

    They actually sent me two different dampers that they were keeping as templates for a new production run.
    I had to send them back.

    I tightened my oil line to the tank and it is closer than yours,...
  18. Replies
    225
    Views
    25,761

    I was told it would be near the end of the year...

    I was told it would be near the end of the year before the fork dampers would be available.
    "Gentle persuasion" seems to be normal with a lot of repo parts.
    I tried to post a video of the bike...
  19. Replies
    225
    Views
    25,761

    Steve, I fitted my tanks to my 29 yesterday, and...

    Steve,
    I fitted my tanks to my 29 yesterday, and it looks like I have the same issue as you with the hand oiler line.
    The line in the photo is hand tight only, but it looks like the line to the...
  20. Replies
    12
    Views
    540

    Rubone, Belt sander typically have crowned...

    Rubone,

    Belt sander typically have crowned pulleys, hence the need for tracking adjustment. The physics are different to a flat pulley, although some may have a 2 degree pitch that you cannot see....
  21. Replies
    13
    Views
    720

    I have a number of bikes that sit around for...

    I have a number of bikes that sit around for extended times. I spend more time building my bikes that riding them.
    When they were filled with pump gas, every time I went to ride them I would have to...
  22. Replies
    12
    Views
    540

    I have used a number of belt drives over the...

    I have used a number of belt drives over the years, and generally I prefer them over a chain drive.
    However, as with most things, they are not as perfect as the manufactures would have you believe....
  23. Replies
    2
    Views
    369

    Martin, I have a spare rear section I don't...

    Martin,
    I have a spare rear section I don't need. Needs some panel beating, and one small crack.
    Send me a PM.
    25883
  24. Replies
    10
    Views
    484

    I don't mean to be pedantic here but an ammeter...

    I don't mean to be pedantic here but an ammeter shows current though it, not voltage.
  25. Replies
    27
    Views
    1,184

    When installing motors this way, be aware that...

    When installing motors this way, be aware that some motors will only go in one way. Often the motor will need to be installed from the right hand side of the bike.
    Looks like it didn't matter with...
Results 1 to 25 of 228
Page 1 of 10 1 2 3 4