Search:

Type: Posts; User: duffeycycles

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    18
    Views
    513

    Sorry Cotton,I did not finish the...

    Sorry Cotton,I did not finish the sentence..edited
    I use the asbestos on aluminum
    I have seen the imprint in aluminum as well
  2. Replies
    18
    Views
    513

    Copper for aluminum causes issues on some 45"...

    Copper for aluminum causes issues on some 45" because of narrow area near the motor mount.
    K-models had no gasket?
    Sporty was copper..I think
  3. Replies
    18
    Views
    513

    From Chris:The MoCo always used copper head...

    From Chris:The MoCo always used copper head gaskets until the war time restrictions on copper during WWII came into effect. It was at that time that they started using asbestos gaskets. Copper...
  4. Replies
    13
    Views
    890

    Thanx Mark,I thought this was a 23 case

    Thanx Mark,I thought this was a 23 case
  5. Replies
    13
    Views
    890

    I had 2 1915 J motors,early & late & the bottom...

    I had 2 1915 J motors,early & late & the bottom numbers looked like different format from each other
    An early 1920s right case on my wall has B3 space 890 bottom number..my clock!
  6. Looking back at the original post,he says the...

    Looking back at the original post,he says the 1939 45" fork legs were VL rigid & knuck spring fork.They are not that,they are different lengths etc.etc.
  7. I don'tcare what Bob says about me. I'm already...

    I don'tcare what Bob says about me.
    I'm already on his crap on list like 1/2 his potential customers.
    As my mother would say, if you hate someone & they don't hate you back it only hurts you.
    i...
  8. Very sad deal.I met Paul at the swaps,very nice...

    Very sad deal.I met Paul at the swaps,very nice to me.As far as Bob's comment above...no comment.I don't think we can save everybody,we all have our time.
    26083
  9. Replies
    13
    Views
    962

    Bulbs popping could be the cutout is not set...

    Bulbs popping could be the cutout is not set right & is running high voltage when revved.They will start,run,rev but will surge when trying to maintain a steady low speed
  10. Replies
    13
    Views
    962

    Firing on one is usually the repop coils or...

    Firing on one is usually the repop coils or serious intake leak & yes they can go bad that fast
  11. Replies
    22
    Views
    1,489

    303 is resistor copper core Starklite calls for...

    303 is resistor copper core
    Starklite calls for their Indian script = NGK B7HS or Champion J6..non resistor plugs
    I hate Autolite plugs
  12. Replies
    22
    Views
    1,489

    All carbs need to be adjusted for the motor. You...

    All carbs need to be adjusted for the motor.
    You need to read the part after initial adjustments & do those adjustments.TWICE!!!
    There is no setting that fits all motors & carbs.
  13. Replies
    7
    Views
    1,125

    1932 Ford pickup with Little Base Indian flanked...

    1932 Ford pickup with Little Base Indian
    flanked by Dick Klamfoth,Bill Tuman,Bobby Hill at National motorcycle Museum Anamosa Iowa
    Vintage Rally
    25864
  14. Replies
    32
    Views
    2,609

    Mike wilson in Cedar Rapids also dropped the HD...

    Mike wilson in Cedar Rapids also dropped the HD franchise & went with honda in 1965,because of pressure from the Motor Co.He had originally been an HD financed startup dealership.
  15. Replies
    6
    Views
    908

    I make seal installers on my lathe out of PVC...

    I make seal installers on my lathe out of PVC like Robbie said.I take dimensions & go to hardware store & buy a pipe or usually connector & turn it down.The seal is supposed to be .050" in from face...
  16. Replies
    7
    Views
    855

    Do't forget the races on friday nite 25562

    Do't forget the races on friday nite
    25562
  17. Replies
    7
    Views
    855

    2019 Blackhawk poster 25546

    2019 Blackhawk poster
    25546
  18. Tires have maximum pressure values on them not...

    Tires have maximum pressure values on them not the recomended pressure for a particular vehicle.A Mercedes may say 28 psi & the tire says max 40.Rigid frame bikes require lower pressure to be...
  19. Replies
    53
    Views
    4,952

    many years back a USA guy sold 12 knucks to...

    many years back a USA guy sold 12 knucks to europe.The guy left the titles & said he did not need them so make some more!
  20. Replies
    7
    Views
    1,346

    marking pens don't work if they reuse a dollar &...

    marking pens don't work if they reuse a dollar & make a 100..my friend got a counterfit $100 from an Aussie a few years ago at Davenport.Couldn't find the guy after he noticed it.
  21. Replies
    8
    Views
    754

    They had all of that + fender light,sidecar light...

    They had all of that + fender light,sidecar light & taillight without ever knowing what an LED bulb is
  22. Replies
    17
    Views
    1,516

    To go with Jerry's post.Even HD has used the term...

    To go with Jerry's post.Even HD has used the term Knucklehead in recent t-shirts & other parlor items,so they have used a term coined elsewhere to discribe a bike that they never originally called...
  23. Replies
    17
    Views
    1,516

    Actually Fletcher,We have discussed this on the...

    Actually Fletcher,We have discussed this on the forums several times thru the years.
  24. Is there a difference in the angle of...

    Is there a difference in the angle of mounting?The ones shown look angled to match the fork perches.
  25. Replies
    17
    Views
    1,516

    And they don't call the new bike an M80.or the...

    And they don't call the new bike an M80.or the last one a twinkie..
    .but I can't help myself
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4