Search:

Type: Posts; User: hdhikaru

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    265

    wire rub..... I see,,, when light off, ...

    wire rub..... I see,,, when light off, runs good. so.... the wire going to L terminal touch the body or ... in gen,,,, ??
  2. Replies
    3
    Views
    265

    46WL engine stop when light on.

    hi there,
    advice please 46WL running nicely with three brush 6V gen. but when light on, red lamp on and engine stop..... .. bad battery... or bad gen.. should turn the third...
  3. Replies
    14
    Views
    975

    25038 how about this sidecar loop. looks...

    25038 how about this sidecar loop. looks original to me but no casting#. grind off or repop..?? advice please. Shin
  4. Replies
    14
    Views
    975

    thank you guys! any advice about the#s ...

    thank you guys! any advice about the#s 404..... ? please take a look closely..
  5. Replies
    2
    Views
    355

    check piston size

    hi there,

    just checking the piston size from 73 FXE.
    25028

    just see B on top but other than that... nothing can be seen.

    is this STD original piston? please advice.

    tks
  6. Replies
    2
    Views
    260

    38 frame identification ②

    hi there,

    please see attached pics again..
    25024 25025 25026 25027

    these place was brazed at the factory but looks welded. just wonder there places are commonly fixed like this? ...
  7. Replies
    14
    Views
    975

    38 frame identification ①

    Hi here、
    any idea..?
    this is a 38 frame I was told. I realized some #s on it... please refer the pics attached.
    25022 25021 25023
    looks 404.. 202...4... these are original stamp or...
  8. Thread: WL oil gauge

    by hdhikaru
    Replies
    10
    Views
    612

    got it!! thanks! :D

    got it!! thanks! :D
  9. Thread: WL oil gauge

    by hdhikaru
    Replies
    10
    Views
    612

    thanks! .. so. upto where should be enough? ...

    thanks! .. so. upto where should be enough? I think the tank should not be filled up .. as the vent pipe should not be covered .....
  10. Thread: WL oil gauge

    by hdhikaru
    Replies
    10
    Views
    612

    WL oil gauge

    hi there,
    one basic question.
    oil level should be between danger and refill line.... right?
    24832

    tks
    Shin
  11. Replies
    9
    Views
    559

    thank you guys! ;)

    thank you guys! ;)
  12. Replies
    9
    Views
    559

    so.... should use small stick or something to...

    so.... should use small stick or something to check the oil level at vertical position?
  13. Replies
    9
    Views
    559

    46WL transmisstion oil

    Hi,
    please advice how do you check if the oil is certain amount in the case?
    just check through this plug hole? 24799

    tks
    Shin
  14. Replies
    14
    Views
    1,117

    thanks you all!! :)

    thanks you all!! :)
  15. Replies
    14
    Views
    1,117

    oil oil oil...

    hi there,

    simple question about engine oil. mixing 50 +60 just to make 55 oil:rolleyes:.... is bad idea? how about mixing revteck and genuine oil ... bad too?

    how...
  16. Replies
    7
    Views
    637

    got it! thanks Mr. Cotton! :)

    got it! thanks Mr. Cotton! :)
  17. Replies
    7
    Views
    637

    ok, thanks Chris. :)

    ok, thanks Chris. :)
  18. Replies
    7
    Views
    637

    Hi Mr,Cotton, I use oil single 50 for the...

    Hi Mr,Cotton,

    I use oil single 50 for the motor. same one for the transmission too? not thicker one ... like 80 or 90?
  19. Replies
    7
    Views
    637

    hi Mr.Cotton, got it! thanks!! :)

    hi Mr.Cotton, got it! thanks!! :)
  20. Replies
    7
    Views
    637

    harley 1937 U transmission rebuilding

    Hi, please advice....
    I just finished rebuilding of 37 U transmission.
    I just seal main drive gear like this... 24469

    so how many cc oil should be in?

    tks
    Shin
  21. Replies
    2
    Views
    526

    I see, thanks!!

    I see, thanks!!
  22. Replies
    2
    Views
    526

    38 frame neck casting mark

    Hi there,

    I was told the frame was 38 original ....
    here is the neck of the bike. 24338

    the cast mark DIF in square is almost gone but you could see " 2 " clearly...
    is that...
  23. Replies
    4
    Views
    697

    thanks !! now I have an idea! Shin

    thanks !! now I have an idea! Shin
  24. Replies
    4
    Views
    697

    thanks !! I see.... I just remember .. the...

    thanks !! I see.... I just remember .. the drive gear is just pressed on :D I will remove it and pressed on the one in the case. thanks!!
  25. Replies
    4
    Views
    697

    transmission speed drive gear

    hi
    I am going to put this drive gear in this case. 2429124290
    this is 15Tx19T but the one in the case is 15Tx17T and the 3rd gear on main shaft is 24T. so.... Do I need change the 3rd...
Results 1 to 25 of 87
Page 1 of 4 1 2 3 4