Consider also that the clutch hub bushing only spins on the shaft when the clutch is in and these bushings are almost always worn loose so minimize the time.
BTW I never trust or use this feature....
Type: Posts; User: tfburke3
Consider also that the clutch hub bushing only spins on the shaft when the clutch is in and these bushings are almost always worn loose so minimize the time.
BTW I never trust or use this feature....
Yeah,re-purposed might be a better description of the mount than homemade.
Tom
To me the seat is Indian ,with the straight ribs,harley pan has the outer ribs curved.Mount I would guess is homemade
The cylinder bores look to have enough scoring to to warrant further inspection.I would pull the cylinders and run hone thru a couple of passes and you will be able to get a better idea if you also...
Thanks,
Tom
Greer list the standard size .876 and has 10,20 and 30 oversize.
I ave a nos shaft,in a nos 1935 frame and it measures .874.
Tom
Curious if the new .871 is an India product.I have seen some...
Just the metal screen,retaining wire and three screws with clips.A big improvement over 34 which had nothing but a plate to keep your pants from sucking in or catching on fire if a backfire.
Tom
i like right throttle like my modern harley.Muscle memory,or lack of ,gets confusing sometimes on my left throttle bike.
BTW I like the brake and gas on the same side ,opposite shifter,as its the...
I would put the cases in front of a space heater ,then hit with a foam type degreaser and scrub brush..Dont glass bead.
Tom
I havent done it but you can get various small diameter endoscopes amazing cheap on ebay or amazon for smart phone, tablet etc.Some indy shops by me use them for quick cylinder bore inspection.Tom
Gotta multi meter?not a guru but set on ohms and read between the battery positive wire and ground with the battery disconnected and you will see an ohm reading.Find out what needs to be...
Have you looked at the gears?Probably chewed up slider or bent mainshaft.I once had a repro slider that didnt last 1000 miles.Cluster gear and bushings,and the right side steel cluster shaft bushing...
The housing pump surface looks good,but like bubbalowe said the top cover needs replacing.Then inspect the shafts,keys and middle case.Not to hard and it seems like you are up to it,but Im not sure...
Pic # 4 not looking to good,but sounds like pump is working.Pic #3 of housing looks good.cant really tell about center case with gears in place.The new spring ,ball and re-seating may help wet...
Thats pretty much it.That show its circulating. its getting supply and returning.After a short,say ten mile ride the tank should be warm to hot.If you drain the sump after the ride and get about a...
Happened on my 34.Sounded like tea kettle.less likely with more gas in the tank.
Tom
I had read that the nipples were over sized slightly on the thread od and they had made oversize nuts to fit.I have seen them on ebay with nuts included.
Tom
Suprised at no lock tab,but I never had a101.I would still put one there.I guess its same as chief.
Those nuts are prone to loosening even with the tab and I use red locktite just to be sure....
Hey Harry,looks like your figuring it out.You made a good point about align.I think your collar or driver must have been off almost 1/4".
If you have the correct collar that puts the sprocket in...
Well it looks like you are paying attention to me.
Obviously the sprocket position will effect chain align,but you have get the sprocket fully on the driver with a full nut and lock tab.
What...
It looks like you need get your sprocket further on the driver.Im more familiar with chiefs but I think its similar.
How does the sprocket fit without the spacer behind it?I set the sprocet,then...
Thanks.If you know the numbers or what year and model BMW I will look it up.
Tom
Because its standing wet sumping that doesnt necessarily indicate a weak or worn pump.If it was wet sumping while running that could indicate a worn return pump.
In my opinion high output is not...
Curious what a new Dixie is. I have a couple India repro batteries on the shelf but not going to fill one this time of year plus they make a mess.
Tom
Thanks,I was using the same chart.The faux box is about 6 1/4 so hopefully it fits.
Tom