Search:

Type: Posts; User: Jerry Wieland

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    264

    Dave Benassi

    Dave was a vintage motorcycle enthusiast to the utmost. He was always willing to educate or listen and learn. He was in to old bikes for the pure joy of it. He will be sadly missed by all who knew...
  2. Replies
    50
    Views
    2,318

    Then there is this guy. ...

    Then there is this guy.


    https://www.ebay.com/sch/lornfornwal0/m.html?item=193047689229&rt=nc&_trksid=p2047675.l2562

    You wait around long enough and your year and model is bound to show up. He...
  3. I suspect that if it is not Nera-Car that the...

    I suspect that if it is not Nera-Car that the parts were made in the Nera-Car factory. Jerry
  4. Replies
    8
    Views
    699

    I think most of the wholesale sellers on the web...

    I think most of the wholesale sellers on the web and else where have fixed very little in their life and could not tell a good piece from a bad. Jerry
  5. Replies
    17
    Views
    978

    Chris HD also never called your beloved 1936 OHV...

    Chris HD also never called your beloved 1936 OHV Deluxe a Knucklehead either. Jerry
  6. New exhaust seats in a 1925 JD front cylinder

    Has anybody ever done this with any luck? I have a good 1925 JDCB cylinder that is nice except it needs more of a seat. I have heard of cutting and installing a seat but I have also heard of them...
  7. Replies
    3
    Views
    491

    Shin If you have adequate voltage when you...

    Shin

    If you have adequate voltage when you start the bike I cannot believe that you have a bad battery. The engine should not stop when the red light comes on. The red light is just a sign that...
  8. Replies
    14
    Views
    1,450

    I think it is the other way around.

    I think it is the other way around.
  9. Replies
    2
    Views
    406

    Shin Your frame is an early one (pre 41) by the...

    Shin Your frame is an early one (pre 41) by the neck casting but I suspect it is 1939 or 1940 and not 1938. It has had some repair at the top motor mount and has had the dash neck casting welded back...
  10. They were not there a year ago either because I...

    They were not there a year ago either because I was looking for them for a friend. Jerry
  11. Replies
    29
    Views
    6,558

    My favorite Tedd story is: I would buy necks for...

    My favorite Tedd story is: I would buy necks for panhead head frames and they always seemed to have the same problem so I marked the neck up inside and lo and behold they sent me the same neck back....
  12. Replies
    10
    Views
    1,381

    Wow Mark you hit a home run. You not only figured...

    Wow Mark you hit a home run. You not only figured out what you have but you got a part # and also how much at least one guy is welling to give for it! Sorry but I do not know how far up this fits but...
  13. Thread: 46 Knuck

    by Jerry Wieland
    Replies
    13
    Views
    1,986

    Flathead You cannot plug the primary chain...

    Flathead

    You cannot plug the primary chain oiler because it is also the crankcase vent. You have to shut the oil off at the pump with the needle and then I reroute the crank case pipe to the rear...
  14. The height adjusting nut is inside the frame...

    The height adjusting nut is inside the frame above that nut that is missing.

    Jerry
  15. The nut that would have held the seat post in is...

    The nut that would have held the seat post in is missing (2nd photo). It is not uncommon for the seat post to stuck quite firmly in the seat tube especially on bikes that have been out in the...
  16. Replies
    3
    Views
    772

    Trade it for a late knuckle frame and put the...

    Trade it for a late knuckle frame and put the glide on that. Jerry
  17. Replies
    4
    Views
    802

    Looks good.

    Looks good.
  18. Definitely not HD. Looks Goulding to my untrained...

    Definitely not HD. Looks Goulding to my untrained eye. Jerry
  19. Replies
    19
    Views
    2,061

    To be really technical later 1937 transmission...

    To be really technical later 1937 transmission case is a one-year only item. Jerry
  20. Replies
    19
    Views
    2,061

    If your serial number is 5000 you most definitely...

    If your serial number is 5000 you most definitely need the case with the cast in 5th boss. Jerry
  21. Replies
    19
    Views
    2,061

    From my experience only the very early 1937's...

    From my experience only the very early 1937's used the transmission without the fifth boss. I see Ralph says mid production and that may be true but in looking at a lot of OEM type 1937's I have only...
  22. Replies
    7
    Views
    1,125

    I do not know about ULH but Chuck at Kickstart...

    I do not know about ULH but Chuck at Kickstart sells me lone pistons all the time for OHV's. I might also have some. I will check. His number 616 245-8991

    Jerry
  23. Replies
    11
    Views
    2,021

    Nice pictures. Thanks Jerry

    Nice pictures. Thanks Jerry
  24. Replies
    10
    Views
    1,532

    Chris In 40 years of looking I have never...

    Chris

    In 40 years of looking I have never seen any even remotely original 41 with a brass intake. I can point you to 10 original paint 47 with brass intakes. Even your buddy Todd when pressed to...
  25. Replies
    27
    Views
    2,878

    Tom I never run any additive in my knucklehead...

    Tom I never run any additive in my knucklehead either. Usually try to use premium when possible but it runs great on anything. Cast iron guides and stainless valves.


    Jerry
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4