Search:

Type: Posts; User: Kozy

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. No outside grease zerks for the spring rod...

    No outside grease zerks for the spring rod bushings, no bosses for the grease zerks on the rockers and the position of the front brake cable clamp mounting screw are consistent with the '37 fork.
  2. Replies
    53
    Views
    4,201

    Look here for some insight.t...

    Look here for some insight.t http://victorylibrary.com/45MAG.htm
  3. Replies
    4
    Views
    438

    Greg, Check your inbox.

    Greg,
    Check your inbox.
  4. Replies
    53
    Views
    4,201

    How many times have you seen an ad for a model...

    How many times have you seen an ad for a model U/UL/ULH motor and fuel tanks? Some where another knuckle is born.
  5. Thanks for the info, I have experience with both...

    Thanks for the info, I have experience with both Ruby and Stay Silv. I should have thought "tinning fluid".
  6. Soldering requires absolute cleanliness. How do...

    Soldering requires absolute cleanliness. How do you go about cleaning the damaged area to ensure penetration of the molten solder?
  7. You're right and continuing with that attitude an...

    You're right and continuing with that attitude an antique could evolve into a fossil!
  8. Replies
    6
    Views
    1,974

    Thank you both

    Thank you both
  9. Replies
    6
    Views
    1,974

    Does anyone reproduce the glass lens for this...

    Does anyone reproduce the glass lens for this light?
  10. Replies
    10
    Views
    4,817

    The bracket the stand leg fits into may be for a...

    The bracket the stand leg fits into may be for a rigid frame.
  11. Replies
    20
    Views
    7,007

    Should the spool be soldered to the cable casing?

    Should the spool be soldered to the cable casing?
  12. Replies
    25
    Views
    9,162

    Is Brooks leather any good? At one time it was...

    Is Brooks leather any good? At one time it was the thing to have here in Michigan. I don't have any experience with Schott leather but have their down filled hunting gear from the 70's and it has...
  13. Thread: Steering damper

    by Kozy
    Replies
    5
    Views
    2,423

    After soaking in oil and cutting the end off put...

    After soaking in oil and cutting the end off put it in a hydraulic press and push it out.
  14. Replies
    16
    Views
    6,370

    Millwrights have been using the shim type shown...

    Millwrights have been using the shim type shown in the ebay listing to align coupled shafts for years. They're available from industrial suppliers like McMaster-Carr for about a buck apiece.
  15. Replies
    17
    Views
    11,235

    Has S&S given up on BT flathead cylinders and...

    Has S&S given up on BT flathead cylinders and heads?
  16. Jerry, Thanks for the reply and photos. I didn't...

    Jerry, Thanks for the reply and photos. I didn't realize there were differences in the shape of the main brace. You have a great eye for detail.
  17. Brazed Offset?

    http://www.ebay.com/itm/141255447562?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2648

    Here's an ebay listing of an offset fork with the rigid leg spring perch brazed and having the inside bosses...
  18. Replies
    17
    Views
    11,235

    11 fin 74" cyl. casting nos. 120-38 front,...

    11 fin 74" cyl. casting nos. 120-38 front, 120-381 rear
  19. Replies
    20
    Views
    8,653

    Model U ballance factor

    Cotton,
    I'm not a machinist or a engine builder so I don't know all the things that effect selection of balance factor. All I know is what I've heard and the low factor for the VL surprised me....
  20. Replies
    20
    Views
    8,653

    How do VL flywheels compare to UL flywheels in...

    How do VL flywheels compare to UL flywheels in regard to mass?
  21. Thread: !940's rear axels

    by Kozy
    Replies
    5
    Views
    2,052

    Thanks, could it be used on a knuckle frame?

    Thanks, could it be used on a knuckle frame?
  22. Thread: !940's rear axels

    by Kozy
    Replies
    5
    Views
    2,052

    !940's rear axels

    I have two rear axels that look to be 36-47 vintage. One matches the description and measurements in Palmer's book exactly. The other is the same length and diameter except at the head were the step...
  23. Replies
    68
    Views
    41,357

    Did you use a through pin in the casting holes or...

    Did you use a through pin in the casting holes or just weld to the tube slide into them? Thanks for the reply.
  24. Replies
    68
    Views
    41,357

    Alan, Did you weld or braze the neck casting?...

    Alan,
    Did you weld or braze the neck casting? Can you provide more detail on the installation? Thanks.
  25. Replies
    14
    Views
    6,395

    Thanks Tom.

    Thanks Tom.
Results 1 to 25 of 63
Page 1 of 3 1 2 3